How to clean a macbook keyboard without water damage

#HOW TO CLEAN A MACBOOK KEYBOARD WITHOUT WATER DAMAGE PRO#

To avoid damage, buy a wire keycap puller. To get keycaps off, you can pry them up with a screwdriver or spudger. All mechanical keyboards have removable keycaps. If you're using a cheap membrane board (like the ones that ship with desktop towers), you might have to check with the maker to ensure the keycaps can be removed. Be extra careful with the legends on cheap keyboards-the pad printing might not survive a vigorous cleaning intact. Still use a cotton swab to control how much you apply to the key. If you're worried about damaging the keycaps, you can use water with a few drops of laundry detergent or diluted Simple Green instead. The basics from above still apply: use compressed air and clean keycaps with rubbing alcohol (after testing). There are a few more intricacies when it comes to the externalВ keyboards you plug in via USB. To put the key back, line the keycap up and push it back down starting with the bottom edge. With the keycaps off, use compressed air to blow out all the dust and hair. Let me know if you have any questions or if I left anything out.To remove the keys, slip your tool under the top of the cap and gently lift it up.

Pretty sure I would've voided it a few times over already, but my MBP is not under warranty.ДЄny advice or information you could give would be greatly appreciated. I have not attempted to power on since the forced power down at the time of the spill. So it's been about 60 hours since the initial spill.

Disconnected the keyboard cable from the keyboard connector, took the photos linked in the album above, and decided to post here before proceeding.

Found a few drops of standing water on the I/O board cable bracket and corrosion on the keyboard connector and keyboard cable and visible water marks on the large-ish metal rectangle in the middle of the logic board.

Finally (too late I assume) faced my fear and opened up the case, disconnected the battery, and assessed the damage.

Then I would have flushed the keyboard with bottled water, shaken out what I could and put it in a plastic bag, open, then inside a bag of rice for a couple of days or so.

Read that I should air it out keyboard face down, so let it sit keyboard facedown over an open crate for ~36 hours. IF this had been me, I think I would have turned the computer off and removed the battery (don't know if that's possible on a MacbookPro).

Left the MBP on its right side, open, over an absorbent cloth for 24 hours.

for about 10 minutes until there was no water noticeably leaving the chassis

Grabbed some canned air and went to town blasting air through the left side ports, the fan vents, etc.

Immediately turned MBP on its side with right side facing down to drain (pretty sure this was not a great decision.

DonвЂ™t place the cover on your keyboard until it has dried completely, because doing so may permanently damage your keyboard.

After about a second, I heard the fan kick in, then the machine powered off normally as it would from a forced shutdown via power button. DonвЂ™t use hot water to clean your silicone keyboard cover.

this works for the logic board but any part that is porous like the keyboard & trackpad will need to be taken apart or replaced.All.

#HOW TO CLEAN A MACBOOK KEYBOARD WITHOUT WATER DAMAGE PRO#

In a panic, lifted up MBP, turned upside down (keyboard facing down) while mashing the power button. Frequent question, how do I clean my MacBook Pro spilled keyboard Using cotton swabs (Q-Tips) wipe down what you can see if its a lot you may need to dip the part in a tub of distilled water and use a small paint brush or soft toothbrush to scrub the areas.

It is safe to use isopropyl to clean the keyboard cable and connector.

With MBP open and powered on, spilled water across keyboard. Remove the logic board and clean any corrosion with a toothbrush and 95+ isopropyl, there might be some on the other side.

In case more information could be helpful, here's a detailed timeline of events and actions I took, some bad, some worse:

Is it a stupid idea to test/power on the system after cleaning the keyboard cable/connector without first removing the entire logic board and inspecting the other side for corrosion?.

What has already likely been killed (keyboard?), and what further damage do I risk testing those components after cleaning versus replacing them up front (if that's even possible).

Do I need to do an alcohol bath (this terrifies me) of the whole logic board to effectively clean the keyboard connector or can it be cleaned safely/effectively using qtips etc?.

Can the keyboard cable be cleaned safely/effectively like most components, with isopropyl alcohol?.Short version: spilled water on MBP, upon opening it up a few days later discovered corrosion on the keyboard cable connector and the keyboard cable itself (album here: ).Д«asically I'm trying to understand the best approach to minimize further damange and increase the likelihood of getting my MBP back and running: I have a 13' MacBook Pro Retina Display, early 2015, model A1502, 2.7Ghz

How to clean a macbook keyboard without water damage